Harmonic Drive Reducer Shaft Type model SHF-S-14 / SHF-S-17 / SHF-S -20 / SHF-S -25 / SHF-S-32. SHF-S type is the shaft type of GIGAGER harmonic gear series. The principle of GIGAGER harmonic gear reduction is to use the relative motion of the Flexspline, Circular Spline and the wave generator, mainly the controllable elastic deformation of the flexspline to realize the motion and power transmission.

**1. ****What is the Product Features of GIGAGER Harmonic Drive?**

• High cost performance

• High efficiency

• Low backlash

• High rigidity

**2. ****SHF Shaft Series Harmonic Drive**

Series | Type | Spec | Gear Ratio | |||||

SHF | S ( Shaft ) | 14 | 30 | 50 | 80 | 100 | - | - |

17 | 30 | 50 | 80 | 100 | - | - | ||

20 | 30 | 50 | 80 | 100 | 120 | - | ||

25 | 30 | 50 | 80 | 100 | 120 | 160 | ||

32 | 50 | 80 | 100 | 120 | - | - |

For more series CSF, SHD, CSD, please see the attached Catalogue. (download the PDF in this page)

**Model : SHF-S-14**

Items | Gear Ratio | ||||

30K | 50K | 80K | 100K | ||

Rated Torque ( Input 2000r/min ) | N.m | 3.8 | 5.1 | 7.4 | 7.4 |

Permissible Maximum Torque (Start • Stop ) | N.m | 8.6 | 17 | 22 | 27 |

Permissible Maximum Value of Average Load Torque | N.m | 7.8 | 6.6 | 10.5 | 10.5 |

Instantaneous Permissible Maximum Torque | N.m | 16 | 33 | 45 | 51 |

Permissible Maximum Input Rotating Speed | r/min | 8000 | 8000 | 8000 | 8000 |

Permissible Average Input Rotating Speed | r/min | 3500 | 3500 | 3500 | 3500 |

Backlash | Arc sec | ≦ 20 | ≦ 20 | ≦ 10 | ≦ 10 |

Designed Lifespan | hour | 10000 | 10000 | 15000 | 15000 |

**Model : SHF-S-17**

Items | Gear Ratio | ||||

30K | 50K | 80K | 100K | ||

Rated Torque ( Input 2000r/min ) | N.m | 8.4 | 15.2 | 21 | 23 |

Permissible Maximum Torque (Start • Stop ) | N.m | 15.2 | 32 | 41 | 52 |

Permissible Maximum Value of Average Load Torque | N.m | 11.5 | 25 | 26 | 38 |

Instantaneous Permissible Maximum Torque | N.m | 29 | 66 | 83 | 108 |

Permissible Maximum Input Rotating Speed | r/min | 7000 | 7000 | 7000 | 7000 |

Permissible Average Input Rotating Speed | r/min | 3500 | 3500 | 3500 | 3500 |

Backlash | Arc sec | ≦ 20 | ≦ 20 | ≦ 10 | ≦ 10 |

Designed Lifespan | hour | 10000 | 10000 | 15000 | 10000 |

**Model : SHF-S-20**

Items | Gear Ratio | |||||

30K | 50K | 80K | 100K | 120K | ||

Rated Torque ( Input 2000r/min ) | N.m | 14 | 24 | 32 | 38 | 38 |

Permissible Maximum Torque (Start • Stop ) | N.m | 26 | 53 | 70 | 78 | 83 |

Permissible Maximum Value of Average Load Torque | N.m | 19 | 32 | 45 | 47 | 47 |

Instantaneous Permissible Maximum Torque | N.m | 48 | 93 | 121 | 140 | 140 |

Permissible Maximum Input Rotating Speed | r/min | 6000 | 6000 | 6000 | 6000 | 6000 |

Permissible Average Input Rotating Speed | r/min | 3500 | 3500 | 3500 | 3500 | 3500 |

Backlash | Arc sec | ≦ 20 | ≦ 20 | ≦ 10 | ≦ 10 | ≦ 10 |

Designed Lifespan | hour | 10000 | 10000 | 15000 | 15000 | 15000 |

**Model : SHF-S-25**

Items | Gear Ratio | ||||||

30K | 50K | 80K | 100K | 120K | 160K | ||

Rated Torque ( Input 2000r/min ) | N.m | 26 | 37 | 60 | 64 | 64 | 64 |

Permissible Maximum Torque (Start • Stop ) | N.m | 48 | 93 | 130 | 149 | 159 | 167 |

Permissible Maximum Value of Average Load Torque | N.m | 36 | 52 | 83 | 103 | 103 | 103 |

Instantaneous Permissible Maximum Torque | N.m | 90 | 177 | 242 | 270 | 289 | 298 |

Permissible Maximum Input Rotating Speed | r/min | 5500 | 5500 | 5500 | 5500 | 5500 | 5500 |

Permissible Average Input Rotating Speed | r/min | 3500 | 3500 | 3500 | 3500 | 3500 | 3500 |

Backlash | Arc sec | ≦ 20 | ≦ 20 | ≦ 10 | ≦ 10 | ≦ 10 | ≦ 10 |

Designed Lifespan | hour | 10000 | 10000 | 15000 | 15000 | 15000 | 15000 |

**Model : SHF-S-32**

Items | Gear Ratio | ||||

50K | 80K | 100K | 120K | ||

Rated Torque ( Input 2000r/min ) | N.m | 72 | 112 | 130 | 130 |

Permissible Maximum Torque (Start • Stop ) | N.m | 205 | 289 | 325 | 335 |

Permissible Maximum Value of Average Load Torque | N.m | 103 | 159 | 208 | 205 |

Instantaneous Permissible Maximum Torque | N.m | 363 | 540 | 635 | 652 |

Permissible Maximum Input Rotating Speed | r/min | 4500 | 4500 | 4500 | 4500 |

Permissible Average Input Rotating Speed | r/min | 3500 | 3500 | 3500 | 3500 |

Backlash | Arc sec | ≦ 20 | ≦ 10 | ≦ 10 | ≦ 10 |

Designed Lifespan | hour | 10000 | 15000 | 15000 | 15000 |

**3. ****Why choose GIGAGER?**

**4. ****Related Knowledge**

**Mechanic of Harmonic Drive**

The strain wave gearing theory is based on elastic dynamics and utilizes the flexibility of metal. The mechanism has three basic components: a wave generator (2 / green), a flex spline (3 / red), and a circular spline (4 / blue). More complex versions have a fourth component normally used to shorten the overall length or to increase the gear reduction within a smaller diameter, but still follow the same basic principles.

The wave generator is made up of two separate parts: an elliptical disk called a wave generator plug and an outer ball bearing. The gear plug is inserted into the bearing, giving the bearing an elliptical shape as well.

The flex spline is shaped like a shallow cup. The sides of the spline are very thin, but the bottom is relatively rigid. This results in significant flexibility of the walls at the open end due to the thin wall, and in the closed side being quite rigid and able to be tightly secured (to a shaft, for example). Teeth are positioned radially around the outside of the flex spline. The flex spline fits tightly over the wave generator, so that when the wave generator plug is rotated, the flex spline deforms to the shape of a rotating ellipse and does not slip over the outer elliptical ring of the ball bearing. The ball bearing lets the flex spline rotate independently to the wave generator's shaft.

The circular spline is a rigid circular ring with teeth on the inside. The flex spline and wave generator are placed inside the circular spline, meshing the teeth of the flex spline and the circular spline. Because the flex spline is deformed into an elliptical shape, its teeth only actually mesh with the teeth of the circular spline in two regions on opposite sides of the flex spline (located on the major axis of the ellipse).

Assume that the wave generator is the input rotation. As the wave generator plug rotates, the flex spline teeth which are meshed with those of the circular spline slowly change position. The major axis of the flex spline's ellipse rotates with wave generator, so the points where the teeth mesh revolve around the center point at the same rate as the wave generator's shaft. The key to the design of the strain wave gear is that there are fewer teeth (often for example two fewer) on the flex spline than there are on the circular spline. This means that for every full rotation of the wave generator, the flex spline would be required to rotate a slight amount (two teeth in this example) backward relative to the circular spline. Thus the rotation action of the wave generator results in a much slower rotation of the flex spline in the opposite direction.

For a strain wave gearing mechanism, the gearing reduction ratio can be calculated from the number of teeth on each gear:

For example, if there are 202 teeth on the circular spline and 200 on the flex spline, the reduction ratio is (200 − 202)/200 = −0.01

Thus the flex spline spins at 1/100 the speed of the wave generator plug and in the opposite direction. Different reduction ratios are set by changing the number of teeth. This can either be achieved by changing the mechanism's diameter or by changing the size of the individual teeth and thereby preserving its size and weight. The range of possible gear ratios is limited by tooth size limits for a given configuration.

Hot Tags: robot joints harmonic drive, China, manufacturers, suppliers, factory, high quality

Previous: Robot Harmonic Drive Gearhead